Видео

You can do that?

Is this doing MPPT like a solar charge controller? Many of us need a little help or a lot of studying to understand.

Can u semd me schematic

سلام مهندس عزیز شما کجا کار میکنید

सर जी अपना नंबर डाल देना

Sar

Can you share the circuit diagram of the PDM Controlled induction heater? it works perfectly. I also designed PLL controlled 100khz induction heater circuit but controlled the power using UCC3895 phase shifting Full Bridge integrated circuit. However, I could not solve the snubbar problem. I also used a second method by checking the dc bus current and voltage of the Full Bridge inverter circuit. You used a different transportation method. It caught my attention. Thank you.🙂

Cool :)

Hello my dear friend. Your project is great. I could not fully understand the serial-parallel topology. I would be very grateful if you could send me the schematics by e-mail. If you can't do that, my question is, do I have a chance to catch resonance by changing the frequency of the power circuit instead of this series circuit?

Can u semd me schematic

Excelente proyecto 😸

Hello sir which microcontroller used ,and did u use CT to measure zcd and pll .

太慢了😂

Awsome, do you use bulk capacitors after rectifying the AC mains?

tuning for stable UH setting...is right??

I need one.can you send me your contact.

Hello sir which microcontroller u used to generate pwm

Hello can you share the schematics and specifications

ماشالله

Nice project. Want to build one. Can you help?

I learned nothing thanks.

Price kya hai is machine ki

This is an ultrasonic device, nothing special.

Whisky price

Hi.im newbie in electronics and i have a question. Can we use all heaters as a melting device?or a heater can only be used for forging?

ebay 20 amp 12-32 volt board: i figure resonance is from the 2 toroid inductors and the 2 .3 uF capacitors. the coil(not supplied) is the series resistance. I had trouble with the coil connecter smoking. I resoldered and retightened. I soldered joints that had resistance. I used a D cell for the coil form. 9 turns. A bit better still. Then I soldered the coil to the board. I put a 3/8 bolt in the coil on cardboard. After about several minutes the bolt was orange hot. I shut off the silicon valley power supply. The 1000 watt board(24 volts) might start to have problems. 2 capacitors is less resistance . ok demonstrator board. recheck capacitor - under load more?

Please send your whatsapp number

عالی

Great job

Impressive Tuning System, but showing results comparatively the same without the tuning, doesnt provide any good information. This presentation should include how the tuning circuit provides advanced performance above other induction systems.

Please , can u upload the plans and details

Dear brother, I need 2 nos. Induction heater 12 kw each for for resturant flat bottom tub water heating/teat, milk, etc pl reply

Bhai ye masi hona meko my WhatsApp number 8602252317

bhai apka phn num

bhai ye machine banwani ha

bhai phn num send kare

can you share the circuit schematic and circuit components i shall be grateful

اگر ممکنه بگو چطور ساختی اینو تشریح کن کار مدارتو تشکر

خیلی باحاله

اون موتور ac با کویل اون چیه

ته بوته در رفت ؟ آقا مجتبی چی بود توپولوژی این مدار شما ؟ بوته رو با چی درست میکنید ؟

Hi. 8008447117 please call me

سلام بچه مازندرانی؟ امکانش هست راهنمایی بکنید تا بسازمش؟ ممنون

ruclips.net/video/wamc237Q-_Y/видео.html&ab_channel=ZedZed

As the load changes so does the resonant frequency. This requires a PLL to lock on to it and feed back the right frequency to the power section. Some old guy on YT who made a similar system. The output of the PLL goes to a VCO which drives the Power driver (PD). The PD in this case must be a Full Bridge to drive the resonant circuit of the output coil. The PLL output is a low frequency level which will also drive a motor shaft that moves the core of the resonant inductor coil in order to change the frequency. So if anybody there wants to make this self adjusting heater then just make a block diagram to follow what I wrote. I cannot put drawings in this post. Once you make the block diagram you can also design the schematic for it. If you cannot design the schematic then it is no good if he gives you a copy because the system is too complicated for someone who does not have the skill to design the circuit.

schematic

induction heater diagram?

can you share your details on butogara@gmail.com

hello do you have a plan of this oven? can I contact you? thank you

very nice work . Please share your detail on ajantapipes@yahoo.com